Difference between revisions of "MCE firmware"
From MCEWiki
| (21 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | {{ | + | {{Related|Firmware}} |
| − | |||
== Releases == | == Releases == | ||
| − | All firmware can be downloaded from [http://e-mode.phas.ubc.ca/ | + | All firmware can be downloaded from [http://e-mode.phas.ubc.ca/mce/firmware/ http://e-mode.phas.ubc.ca/mce/firmware/]. Release notes for each firmware release can be found below: |
* [[ Clock Card firmware]] | * [[ Clock Card firmware]] | ||
* [[ Readout Card firmware]] | * [[ Readout Card firmware]] | ||
| Line 9: | Line 8: | ||
* [[ PCI card firmware ]] | * [[ PCI card firmware ]] | ||
* [[ Sync Box Firmware ]] | * [[ Sync Box Firmware ]] | ||
| − | * [[ | + | |
| + | See also: | ||
| + | * [[Recommended firmware versions]] | ||
== Loading firmware onto cards == | == Loading firmware onto cards == | ||
| Line 22: | Line 23: | ||
* Always cleanly reset the MCE after a power-up or a reconfiguration! If not, MCE communication with the PC or Sync Box may not work. On MAS prompt, type: '''''mce_reset_clean''''' | * Always cleanly reset the MCE after a power-up or a reconfiguration! If not, MCE communication with the PC or Sync Box may not work. On MAS prompt, type: '''''mce_reset_clean''''' | ||
| − | + | == Implementation Details == | |
| − | |||
| − | MCE | + | * [[ MCE Timing Diagram ]] |
| + | * [[MCE fibre protocol]] - communication between the MCE and the controlling PC over the fibre-optic link | ||
| + | * [[MCE backplane protocol]] - communication between cards within the MCE | ||
| + | * Monitoring MCE Status [[http://www.phas.ubc.ca/%7Emce/mcedocs/system/monitoring_mce_status.doc DOC]] (Nov. 9, 2006) | ||
| + | * [[MCE commands]] | ||
== Firmware Development Tools == | == Firmware Development Tools == | ||
| − | |||
* [[ Quartus II Installation ]] | * [[ Quartus II Installation ]] | ||
* [[ ModelSim SE Installation ]] | * [[ ModelSim SE Installation ]] | ||
** [[ Setting up Altera libraries in ModelSim SE ]] | ** [[ Setting up Altera libraries in ModelSim SE ]] | ||
| − | |||
| − | |||
* [[ JAM Player ]] | * [[ JAM Player ]] | ||
| − | |||
* [[ Convert sof to jic for EPCS64 Serial Configuration Device ]] | * [[ Convert sof to jic for EPCS64 Serial Configuration Device ]] | ||
| − | == | + | == Development notes == |
| − | * | + | * [[intmce:MCE bugs]] |
| − | + | * [[intmce:Firmware Features Under Development]] | |
| − | + | * [[intmce:Closed firmware features]] | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | * | ||
| − | |||
| − | |||
| − | * | ||
| − | + | [[Category:Firmware]] | |
| − | |||
Latest revision as of 15:22, 22 March 2018
Related topics:
Contents
Releases
All firmware can be downloaded from http://e-mode.phas.ubc.ca/mce/firmware/. Release notes for each firmware release can be found below:
- Clock Card firmware
- Readout Card firmware
- Bias Card firmware
- Address Card firmware
- PCI card firmware
- Sync Box Firmware
See also:
Loading firmware onto cards
There are two ways to load MCE firmware:
- Remote firmware update over the MCE fibre interface
- Using Altera-supplied Hardware/Software and MCE Front-panel Connector
Things to bear in mind:
- In v5+ firmware, if you update firmware on any readout card, the card doesn't reply to any command unless the Clock Card is also reprogrammed.
- Always cleanly reset the MCE after a power-up or a reconfiguration! If not, MCE communication with the PC or Sync Box may not work. On MAS prompt, type: mce_reset_clean
Implementation Details
- MCE Timing Diagram
- MCE fibre protocol - communication between the MCE and the controlling PC over the fibre-optic link
- MCE backplane protocol - communication between cards within the MCE
- Monitoring MCE Status [DOC] (Nov. 9, 2006)
- MCE commands
Firmware Development Tools
- Quartus II Installation
- ModelSim SE Installation
- JAM Player
- Convert sof to jic for EPCS64 Serial Configuration Device
