Difference between revisions of "MCE firmware"
From MCEWiki
(→MCE Firmware Releases) |
(→Software Tools) |
||
Line 62: | Line 62: | ||
* [[ JAM Player ]] | * [[ JAM Player ]] | ||
* [[ JRunner ]] | * [[ JRunner ]] | ||
+ | * CVS links | ||
+ | : [[ CVS Firmware Repository ]] | ||
+ | : [[ Quartus II Installation ]] | ||
+ | : [[ ModelSim SE Installation ]] (from scratch) | ||
− | + | * SVN links (We decided (sadly) NOT to migrate from CVS to SVN, if we ever do here is some information:) | |
− | + | : [http://svnbook.red-bean.com/en/1.4/ SVN Manual] | |
− | * | + | : [[ Firmware Accessing the svn repository | Accessing the SVN Repository ]] |
− | + | : [[ Firmware svn commit guidelines | SVN Commit Guidelines ]] | |
− | + | : SVN Basic Operations | |
− | + | :: [[ Firmware svn tagging | Tagging ]] | |
− | + | :: [[ Firmware svn merging | Merging ]] | |
− | We decided (sadly) NOT to migrate from CVS to SVN, if we ever do here is some information: | + | :: [[ Firmware svn branching | Branching ]] |
− | + | :: [[ Firmware svn undelete | Resurrecting Deleted Items ]] | |
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
= MCE Scripting = | = MCE Scripting = |
Revision as of 15:33, 4 March 2010
Contents
Critical Notes
- Always cleanly reset the MCE after a power-up or a reconfiguration! If not, MCE communication with the PC or Sync Box may not work.
> mce_reset_clean
- After an mce_reset, not all of the DAC outputs are set to zero. In addition, values written to RAM-based registers are not reset. A full reconfiguration is required for a proper reset.
> rs psc cycle_pow 1 > mce_reset_clean
MCE Firmware Releases
- Compatible Versions (CC,RC,BC,AC) . (Lists of versions of firmware to use together.)
- MCE Programming File Conversions. (Converting between sof, pof, jic, and jam files.)
- MCE Firmware Downloads
Revision information on firmware for each card:
- Clock Card (CC)
- Readout Card (RC) Rev. A/B (Stratix I)
- Readout Card (RC) Rev. C/D (Stratix III)
- Bias Card (BC)
- Address Card (AC)
- Power-Supply Unit Controller (PSUC) Rev. 1
- Power-Supply Unit Controller (PSUC) Rev. 2
- Sync Box Firmware
MCE Features and How-To Guides
- Data Acquisition
- Fast Data Acquisition (i.e. at the Frame Rate)
- The STOP Command
- How to Configure Which Readout Cards Report Data (5.x.x+)
- How to Read a Column at the Frame Rate (5.x.x+)
- Rectangle Mode Data (5.x.x+)
- Readout Card
- Data Modes
- Filtered Data & the Digital 4-pole Butterworth Low-pass Filter
- Raw 50 MHz Data
- Flux Jumping
- FSFB Clamping Commands (i.e. To Prevent Unlocked Pixels from Ramping, 5.x.x+)
- Clock Card
- Remote Firmware Update
- Internal Commands
- Arbitrary Waveform Generator (i.e. Maximum Length Sequences for Complex Impedance Measurements, 5.x.x+)
- Ramp Generator
- Temperature monitoring
MCE Firmware Bugs/ Features Under Development
- This section has been moved to the Internal MCE Wiki Bug List.
Hardware Peripherals
Software Tools
- JAM Player
- JRunner
- CVS links
- SVN links (We decided (sadly) NOT to migrate from CVS to SVN, if we ever do here is some information:)
- SVN Manual
- Accessing the SVN Repository
- SVN Commit Guidelines
- SVN Basic Operations