Arbitrary Waveform Generator

Determining the complex impedance of SQUIDS is difficult to do, because it requires overlaying a pattern on top a normal bias value to help differentiate between optical noise and electrical noise.

Commands and Usage

In an effort to determine the complex impedance, the following commands have been implemented.

• Commands:
  • internal_cmd_mode:
  • awg_sequence_len: Specify the length of the AWG sequence that is loaded in RAM. This parameter tells the internal commanding FSM how long the AWG sequence is, and at what index it should restart AWG the sequence.
  • awg_data: Load the AWG sequence into RAM on the Clock Card. The RAM has 8192 indexes. This may be expanded later if there are enough resources still available on the Clock Card.
  • awg_addr: Specify the starting address for reading from or writing to the AWG RAM. This parameter does not affect the memory address of the internal commanding FSM.
  • ramp_step_period: (also used for internal ramps) Specify the number of frame periods between each ramp step.
  • ramp_param_id: (also used for internal ramps) Specify the parameter ID of the register to be ramped.
  • ramp_card_addr: (also used for internal ramps) Specify the card address of the register to be ramped.
  • ramp_step_data_num: (also used for internal ramps) Specify the number of data that are to be written per ramp command.

• Usage:

wb cc internal_cmd_mode 3    //Enable internal AWG commands
wb cc ramp_step_period 10    //This number will most likely match the data_rate, below
wb cc ramp_param_id 153      //LED, for example
wb cc ramp_card_addr 2       //Clock Card, for example
wb cc ramp_step_data_num 1
wb cc awg_sequence_len 8192  //Currently the maximum size of the AWG RAM block

wb cc awg_addr 0             //Set the AWG RAM address to zero before writing new values
wb cc awg_data 1 2 1 2 ...   //Write AWG values
wb cc awg_data 1 2 1 2 ...   //Write more AWG values, appended to the end of the first set of values
...
wb cc awg_data 1 2 1 2 ...   //Write the last few AWG values, which must number as many as specified by awg_sequence_len above

wb cc data_rate 10
wb cc ret_dat_s 1 1000
go cc ret_dat 1

Firmware Details

• Synthesis:
  • At this point in time (13 Jan 2009), the feature has not been testing in hardware -- although the simulations look clean
• Implementation:
  • To enable the AWG internal commands, you set internal_cmd_mode = 3, as shown in the usage, above.
  • When writing to the AWG block using the awg_data command, the AWG address pointer is incremented for every new value written, but the address pointer is not reset following the WB, so that the next WB writes to the next available index in the RAM. Thus, once a series of awg_data commands have been issued to specify an entire AWG sequence, the address pointer must be set to zero manually if one wishes to read back the entire sequence.
  • The awg_addr command also determines the index accessed by the internal AWG commanding state machine. When internal_cmd_mode is set to 3, the state machine begins issuing commands using the value stored at the current index of the AWG RAM. The internal state machine assumes that the AWG begins at index zero of the AWG RAM, and ends at index awg_sequence_len-1. When the index reaches awg_sequence_len-1, it wraps to zero. In contrast, awg_data commands can access indexes past awg_sequence_len-1, if you read/write further.
  • The AWG value is applied immediately following a data packet, and appears in index 7 of the next data-packet header. This index is called "Ramp Value", and is also used to report the ramp value when the MCE is in internal ramp mode (internal_cmd_mode = 2)
  • The AWG commands detailed above are implemented in the Clock Card cc_v05000003_02dec2009 firmware tag available in CVS.
  • The awg_addr register and awg_data RAM are readable, but you should not read them while the Clock Card is applying an arbitrary waveform (internal_command_mode = 3) otherwise you’ll screw up the values that the internal FSM applies.