Difference between revisions of "Readout Card firmware"
From MCEWiki
| Line 22: | Line 22: | ||
** unreliable resetmce. Sometimes, firmware waked up non-responsive on lvds lines. | ** unreliable resetmce. Sometimes, firmware waked up non-responsive on lvds lines. | ||
** In data mode 5 and 9, flux-jump counter is not reported properly due to a sign error. However, flux jumping works fine. | ** In data mode 5 and 9, flux-jump counter is not reported properly due to a sign error. However, flux jumping works fine. | ||
| + | |||
| + | == 3.0.19 == | ||
| + | * '''Filename''' : rc_v03000019_16feb2007_raw.sof (no pof as one is not likely to run with this as regular firmware) | ||
| + | * '''Feautres''' | ||
| + | ** data mode 3 is enabled. | ||
| + | ** filter is disabled as a compromise to fit the raw-mode buffer. | ||
| + | |||
| + | * '''Bugs''' | ||
| + | ** unreliable resetmce. Sometimes, firmware waked up non-responsive on lvds lines. | ||
== Old versions == | == Old versions == | ||
Revision as of 17:11, 25 April 2008
Contents
4.0.6
- Filename : rc_v04000006_15feb2008.sof or .pof
- Feautres
- bugfix: unreliable reset due to unsafe and incomplete state machines is fixed.
- bugfix: flux_jump sign problem fixed, so far proved in const_mode, to be tested in servo_mode with cold setup.
- servo_mode=2 or ramp previously only went from 0 to ramp_amp, but now goes from -8192 to -8192+ramp_amp
- new commands are added: scratch and card_type. Scratch takes 8 values and can be used by software to detect reset.
- slot_id and fw_rev are now integrated as part of all_cards.vhd
- lvds_tx_b=0, This will allow Clock Card to use the secondary backplane lvds line and check whether RC is plugged in.
- filter_coeff in misc_banks_admin commented as it is not implemented and causes timing problems.
- Bugs
- reading gainp/gaini/gaind right after power up hangs the reply datapath to CC. resetmce clears this error as temporary solution. the problem is caused by first read ack of pid_ram_admin.
- slot_id is only set after a resetmce is issued. (using the latest all_cards in the next revision will fix this)
4.0.5
- Filename : rc_v04000005_01nov2007.sof or .pof
- Feautres
- data mode 9 (mixed filt + flux jump) with windowing readjusted compared to data mode 8
- Bugs
- unreliable resetmce. Sometimes, firmware waked up non-responsive on lvds lines.
- In data mode 5 and 9, flux-jump counter is not reported properly due to a sign error. However, flux jumping works fine.
3.0.19
- Filename : rc_v03000019_16feb2007_raw.sof (no pof as one is not likely to run with this as regular firmware)
- Feautres
- data mode 3 is enabled.
- filter is disabled as a compromise to fit the raw-mode buffer.
- Bugs
- unreliable resetmce. Sometimes, firmware waked up non-responsive on lvds lines.
Old versions
- 4.0.4 rc_v04000004_11oct2007.sof data mode 8 added (mixed filt + flux jump)
- 4.0.3 rc_v04000003_19sep2007.sof data mode 7 bit split readjusted to 10b error being bit 4 to 14
- 4.0.2 rc_v04000002_11sep2007.sof pid resolution increased to 10b, data mode 7 added
- 4.0.1 rc_v04000001_06sep2007.sof
- 4.0.0 rc_v04000000_29aug2007.sof supports readout_row_index * bugs
