Difference between revisions of "Template:MCE hardware table"
From MCEWiki
| Line 138: | Line 138: | ||
| | | | ||
{{#if: {{{obsolete|}}}| | {{#if: {{{obsolete|}}}| | ||
| − | + | {{!}}- | |
| − | + | {{!}} Power Supply Unit Assembly (S585) [[http://www.phas.ubc.ca/%7Emce/mcedocs/hardware/tech_description/SCUBA-2%20Power%20Supply%20Specification%20Aug-26-2005%20JM%20WH.doc DOC]] | |
| − | + | {{!}} rowspan="4" {{!}} — | |
| − | + | {{!}} colspan="3" {{!}} | |
| − | + | {{!}}- | |
| − | + | {{!}} | |
: Power Supply Unit Board (S585-103) | : Power Supply Unit Board (S585-103) | ||
| − | + | {{!}} [[http://www.phas.ubc.ca/%7Emce/mcedocs/hardware/schematics/PowerSupplyUnit/PSU_S585_103B_20060502_schematics.pdf PDF]] | |
| − | + | {{!}} B | |
| − | + | {{!}} Obsolete | |
| − | + | {{!}}- | |
| − | + | {{!}} | |
: [[Power Supply Unit Controller]] (S585-102) | : [[Power Supply Unit Controller]] (S585-102) | ||
| − | + | {{!}} [[http://www.phas.ubc.ca/%7Emce/mcedocs/hardware/schematics/PowerSupplyController/PSUC%20S585_102GIss8%20Schematic.pdf PDF]] | |
| − | + | {{!}} G8 | |
| − | + | {{!}} | |
| − | + | {{!}}- | |
| − | + | {{!}} | |
: Power Supply Unit Wiring (S585-104) | : Power Supply Unit Wiring (S585-104) | ||
| − | + | {{!}} [[http://www.phas.ubc.ca/%7Emce/mcedocs/documentation/schematics_pcb/SC2-ELE-S585-104_RevB_PSA_Wiring_Diagram.pdf PDF]] | |
| − | + | {{!}} B | |
}} | }} | ||
|- | |- | ||
Revision as of 14:41, 17 May 2017
| Description | Block Diagram† |
Schematics | Rev. | Features |
|---|---|---|---|---|
| Clock Card [PDF†] (S581) | [PDF] | [PDF] | B5 | |
| Readout Card [PDF†] (S582) | [PDF] | [PDF] | B9 | |
| [PDF] | E0 | Low-power RC | ||
| Bias Card [PDF†] (S583) | [PDF] | [PDF] | D6 | Original design |
| [PDF] | D7/8 | High-current det_bias | ||
| [PDF] | D11 | High-current det_bias/no heater | ||
| [PDF] | E0 | Multiple det_bias lines | ||
| [PDF] | F0 | Multi det_bias & MHz-response bias lines; Low-noise bias lines turned off | ||
| [PDF] | F1 | Power turned off on ln_bias | ||
| [PDF] | F2 | Minor change in ln_bias circuit | ||
| [PDF] | F3 | low 1/f-noise opamp for channel 0-15 | ||
| [PDF] | F4 | low 1/f-noise opamp for channel 15-31 | ||
| Address Card [PDF†] (S584) | [PDF] | [PDF] | C4 | |
| [PDF] | D0 | |||
| Instrument Backplane MCEv1 5 MDM [PDF†] (S587-101) | — | [PDF] | C3 | |
| [PDF] | C5 | |||
| Instrument Backplane MCEv2 5 MDM (C587-201) | [PDF] | A | ||
| Instrument Backplane MCEv2 3 MDM (C587-101) | [PDF] | [PDF] | B | |
| [PDF] | C1 | |||
| [PDF] | C2 | |||
| Bus Backplane MCEv1 [PDF†] (S586) | [PDF] | [PDF] | C | |
| Bus Backplane MCEv2 (C586-101) 3 MDM | — | [PDF] | A | |
| Bus Backplane MCEv2 (C586-201) 5 MDM | [PDF] | D | ||
| Filter Board MCEv1 (S587-111) | — | [PDF] | B2 | |
| Filter Board MCEv2 (C587-111) - 3 MDM | [PDF] | A | ||
| Filter Board MCEv2 (C587-210) - 5 MDM | [PDF] | A | ||
| MDM Breakout Test Board MCEv1 | [XLS] | |||
| Linear Feed Card | — | [PDF] | ||
| †: Not updated since early design stages. | ||||
- Clock Card Dual-Configuration Technical Note [PDF] (SC2-ELE-S8xx-xxx) (Oct. 01, 2003)
- FPGA Configuration Block Diagram [PDF] (SC2-ELE-S560-003)
- Subrack Mounting Instructions [DOC] (SC2-MEC-S580-504)
- Cryostat Mounting Test Results [PDF]
External Hardware and Accessories
| Description | Block Diagram |
Schematics | Revision |
|---|---|---|---|
| 24V Power Supply and Power Distribution [PDF] | [PDF] | Obsolete | |
| 24V Vicor-based Power Supply | [PDF] | C2 | |
|
[PDF] | A | |
| AC-DC Converter Unit and Power Distribution [DOC] | |||
|
[PDF] | A | |
|
[PDF] | A | |
|
[PDF] | A | |
| Synchronizer Box [PDF†] (S589) | [PDF] | ||
|
[PDF] | [PDF] | A2 |
|
[PDF] | ||
|
[PDF] | [PDF] | |
| SDSU PCI Interface Board (San Diego State University) | [PDF] | 5A | |
| Extender Card [PDF] (SC2-ELE-S565-008-003) | [PDF] | ||
| Instrument Bus Tester [PDF] | [PDF] | C | |
| 2-slot Backplane | [PDF] | A | |
| [PDF] | B | ||
†: Note: Both Sync Box enclosures have the same PCB board inside, only the enclosure and the connectors are different. User's Guide is not yet updated for the DC-in enclosure, so all connector references are based on the rack-mount version.
