Open loop data acquisition - Revision history

Dvw at 00:43, 31 August 2016

2016-08-31T00:43:17Z

Dvw at 23:03, 30 August 2016

2016-08-30T23:03:15Z

Mhasse: /* mce_freeze_servo */

2012-12-29T15:53:32Z

‎mce_freeze_servo

Mhasse: /* SQ1 and TES Stages */

2012-12-12T01:54:36Z

‎SQ1 and TES Stages

Mhasse: /* SQ1 and TES Stages */

2012-12-12T01:53:23Z

‎SQ1 and TES Stages

Mhasse at 01:52, 12 December 2012

2012-12-12T01:52:54Z

Mhasse: Created page with 'This article describes the acquisition of open loop data using the MCE. This is useful for characterizing noise contributions from each stage of the amplifier chain, as well as …'

2012-12-12T01:52:11Z

Created page with 'This article describes the acquisition of open loop data using the MCE. This is useful for characterizing noise contributions from each stage of the amplifier chain, as well as …'

New page

This article describes the acquisition of open loop data using the MCE. This is useful for characterizing noise contributions from each stage of the amplifier chain, as well as for identifying the origin of weird contaminating signals.

== mce_freeze_servo ==

The script mce_freeze_servo is invoked as
mce_freeze_servo <stage> [options]

The '''stage''' argument should be one of: '''preamp, sa, sq2, sq1, tes'''.

In all cases, the script will perform the following actions:
* Disable the MCE servo on the SQ1 feedback
* Disable multiplexing of the SQ1 bias
* Sets the [[MCE data modes | data_mode]] to 0 (error signal).

Additional operations are performed depending on the stage argument.

After the script runs, [[mce_run]]] can be used to acquire open loop data. To then recover the original MCE configuration, it is necessary to run [[mce_reconfig]], or something.

=== preamp stage ===

This stage is provided for completeness. In this case the SA bias and SA offset are both set to 0, to facilitate measurement of the MCE preamp (and any noise from the superconducting series array...).

=== SA and SQ2 Stages ===

When stage='''sa''' or stage='''sq2''', all SQ1 biases are set to 0. (Some caution must be taken with row_order in this case; since the script does not alter row_order, only row_select lines appearing in row_order will have their biases zeroed.)

When stage='''sa''' mode, the script will also the SQ2 biases to 0.

=== SQ1 and TES Stages ===

In these cases the script must be invoked with the --row=<row> argument, to specify a particular row to study. The reason that only a single row can be studied is that the feedback on a given column must take a single, constant value, and thus can only be optimized for a single SQ1 (per column).

The good news is that the script will automatically determine the appropriate feedback value, by acquiring locked feedback data for the chosen row prior to disabling the servo.

The only difference between stage='''sq1''' and stage='''tes''' is that in the former case, the script will zero the TES biases (and it will do this before determining the feedback set point).

To acquire noise on all rows, you could write a bash script that looks like this:

filebase=rowdata_121211
for row in `seq 0 32` ; do
mce_reconfig
# Additional configuration (readout rate, etc.)
# ...
mce_freeze_servo sq1 --row=$row
filename=`printf %s%_row02i $filebase $row`
mce_run $filename 10000 s
done

← Older revision		Revision as of 00:43, 31 August 2016
Line 48:		Line 48:
	done		done

−	[[Category:~~Software~~]]	+	[[Category:MCE Script]]

← Older revision		Revision as of 23:03, 30 August 2016
Line 47:		Line 47:
	mce_run $filename 10000 s		mce_run $filename 10000 s
	done		done
		+
		+	[[Category:Software]]

← Older revision		Revision as of 15:53, 29 December 2012
Line 15:		Line 15:
	Additional operations are performed depending on the stage argument.		Additional operations are performed depending on the stage argument.

−	After the script runs, [[mce_run]]] can be used to acquire open loop data. To then recover the original MCE configuration, it is necessary to run [[mce_reconfig]], or something.	+	After the script runs, [[mce_run]] or [[Raw-mode_readout\|mce_raw_acq_1col]] can be used to acquire open loop data. To then recover the original MCE configuration, it is necessary to run [[mce_reconfig]], or something.

@@ Line 32: / Line 32: @@
 In these cases the script must be invoked with the '''--row=<row>''' argument, to specify a particular row to study.  The reason that only a single row can be studied is that the feedback on a given column must take a single, constant value, and thus can only be optimized for a single SQ1 (per column).
-The good news is that the script will automatically determine the appropriate feedback value, by acquiring locked feedback data for the chosen row prior to disabling the servo.
+The good news is that the script will automatically determine the appropriate feedback value, by acquiring locked feedback data for the chosen row prior to disabling the servo.  (By default, the script will issue "wb flx_lp_init 1", resetting the servo, before acquiring the feedback data.  This can be suppressed with the --no-reinit option.)
 The only difference between stage='''sq1''' and stage='''tes''' is that in the former case, the script will zero the TES biases (and it will do this before determining the feedback set point).

← Older revision		Revision as of 01:52, 12 December 2012
Line 18:		Line 18:


−	=== ~~preamp~~ stage ===	+	=== Pre-amp stage ===

	This stage is provided for completeness. In this case the SA bias and SA offset are both set to 0, to facilitate measurement of the MCE preamp (and any noise from the superconducting series array...).		This stage is provided for completeness. In this case the SA bias and SA offset are both set to 0, to facilitate measurement of the MCE preamp (and any noise from the superconducting series array...).

@@ Line 30: / Line 30: @@
 === SQ1 and TES Stages ===
-In these cases the script must be invoked with the --row=<row> argument, to specify a particular row to study.  The reason that only a single row can be studied is that the feedback on a given column must take a single, constant value, and thus can only be optimized for a single SQ1 (per column).
+In these cases the script must be invoked with the '''--row=<row>''' argument, to specify a particular row to study.  The reason that only a single row can be studied is that the feedback on a given column must take a single, constant value, and thus can only be optimized for a single SQ1 (per column).
 The good news is that the script will automatically determine the appropriate feedback value, by acquiring locked feedback data for the chosen row prior to disabling the servo.